knowledge

A slant-bed—also called an inclined-bed or angled guideway—positions the machine ways at an angle to the horizontal. Instead of sliding flat, the carriage moves downward along the slope, using gravity to evacuate chips and lowering the machine’s center of gravity. This design gives Swiss-type lathes extra room for frequent tool changes and long-bar machining.

JSWAY slant-bed Swiss lathe highlights
• Factory-fitted pre-tensioned ball screws and large-diameter angular-contact bearings deliver micron-level positioning accuracy.
• Standard hollow hydraulic chuck and auto-bar-feed interface allow one-setup, non-stop machining of long bars.
• Optional JS-Edge temperature and vibration sensors stream data to the cloud; AI algorithms give early warnings.
• “Slant-bed retrofit kit” lets you convert existing flat-bed machines to JSWAY slant-bed modules, avoiding full-machine replacement costs.
One-sentence promise
Turn gravity into productivity—choose JSWAY slant-bed Swiss lathes and turn every long bar into higher profit.

At JSWAY CNC COMPANY, every high-precision Swiss-type lathe and 5-axis milling & turning center spends 6–24 months “sunbathing” outdoors. This is not romantic craftsmanship but a scientific natural-aging process that releases residual stress.Under daily temperature swings and self-weight creep, casting residual stress drops by 10–20 %, and bed straightness drifts less than 3 μm per meter over 12 months, creating a zero-deformation foundation for final precision machining.No phase change, no hardness loss—natural aging is the invisible insurance for ultra-precision machine bases.Tight delivery schedule? JSWAY offers a “natural aging + vibration aging” package, retaining dimensional stability while cutting total lead time to 3–6 months, helping you win high-end markets faster.Choose JSWAY CNC COMPANY and let time power your precision machines.

In short: pick the workpiece first, then the machine, let the process dictate the rest, balance accuracy against maintenance, and finalize with budget and brand. A hydraulic chuck chosen this way will give any gang-type lathe or turn-mill center the triple benefit of secure clamping, fast change-over, and low total cost.

When a workpiece features bosses, grooves, or angled surfaces, conventional chucks often require multiple setups that waste the high-speed potential of a Swiss lathe. JSWAY’s custom fixtures are designed to mirror the part profile, allowing the machine to complete everything in one clamping.• Quick-change interface: swap fixtures without re-indicating, eliminating downtime between batches.• Built-in clearance: the fixture body itself provides tool relief, so back-working spindles and live tool turrets can machine inner and outer diameters, face slots, and angled holes simultaneously—no second setup needed.• Stable support: multi-point form contact suppresses vibration at high rpm, giving sensors cleaner data and making thermal compensation and tool-life predictions more reliable.JSWAY offers complimentary custom-fixture evaluations: send your part model and receive a tailored fixture concept along with a full process simulation that aligns cycle time with quality.Choose JSWAY and turn complex contours into simple profit—one clamping, full completion.

Purpose of Evaluation
Turn-mill machining squeezes multiple operations into a single machine, shortening cycle time but lengthening the error chain. Process evaluation is the virtual rehearsal of the entire machining cycle in digital space to find bottlenecks, collisions, over-cuts or residual-stress hot spots—eliminating costly trial cuts and downtime.
[JSWAY Solution] JSWAY CNC provides the JS-CAM evaluation service: upload your part model and receive a complete process-simulation report that exposes the vast majority of hidden risks before metal is cut.

Daily “Clean + Lubricate” as the Baseline
After each shift, remove chips and coolant residue from the fixture surface and collet jaws with a soft cloth or air gun to prevent corrosion and re-clamping errors. Every eight hours, apply a trace of rust preventive oil to spring collets, guide bushings and other moving parts; once a week, add a thin coat of grease to ball-screw nuts and hydraulic cylinder rods to reduce wear. Before any prolonged shutdown, spray anti-rust oil on internal bores and locating faces and wrap them in wax paper or plastic film.
Precision Calibration & Data Closure
Use ring gauges or master bars every month to verify repeatability of the fixture; log results in the MES. If deviation exceeds 0.005 mm, trigger compensation or repair. For quick-change systems (HSK/Capto), check taper contact percentage every six months—target ≥ 80 %. If lower, re-grind or replace.
Spare Parts & Training
Keep minimum stock of jaws, seals and springs to enable replacement within two hours. Hold quarterly on-machine training sessions for operators on correct clamping practices and anomaly recognition to eliminate abusive clamping.
In short, embedding “clean–lubricate–inspect–calibrate” into daily SOP keeps the fixture delivering micron-level accuracy, reduces downtime, and extends overall machine life.

Six preventive measures


Environment control: keep the workshop at a stable temperature and low humidity; exclude dust and corrosive gases to reduce chemical wear on guideways and screws.


Daily checks: remove chips every shift and inspect the lubrication of the spindle, bearings, ball screws and guideways; act on any abnormality immediately.


Preventive lubrication: replace lubricants on schedule and keep the lubrication system unobstructed to minimize fatigue wear.


Accuracy monitoring: use laser interferometers or ball-bar systems monthly to measure geometric errors and compensate for ball-screw backlash or guideway straightness in time.


Electrical health checks: periodically examine cables, relays and cooling fans to prevent hidden aging caused by overheating.


Data monitoring: onboard sensors record spindle current, vibration and temperature; cloud-based analytics predict early bearing or tool failures.


Why prevention matters
• Ensures machining consistency: eliminating micron-level error sources keeps batch dimensions stable and reduces scrap.
• Extends machine life: preventing micro-cracks from growing can prolong overall life by more than 20 %.
• Reduces unplanned downtime: planned maintenance replaces emergency repairs, increasing overall equipment effectiveness (OEE) by 10 % or more.
• Cuts total cost: lower spare-parts inventory, labor and lost-production costs can save tens of thousands of dollars per machine annually.
• Enhances brand reputation: consistent on-time, defect-free deliveries strengthen customer trust and secure future orders.

Optimizing cycle time on turn-mill machining centers is crucial for boosting productivity and reducing costs. It requires a systematic approach addressing machine tools, cutting tools, processes, programming, fixtures, and material flow.